Refashion faux leather zebra print blazer

Black zebra print blazer before trnasfrmation www.cardinalsewingnest.com
THRIFT SHOP SPLURGE!

Found this very nice faux leather blazer at my favorite second hand store for $7.00. It looked as if it had never been worn and I liked the black on black zebra print. The blazer fit nicely and didn’t need any adjustments.

Let’s see what I can do with it. I have an idea that can be completed in about 2 hours.

I have seen many refashioned versions of this jacket by Burberry Prorsum.

THIS JACKET IS FROM A FEW SEASONS BACK

My thrift shop blazer is ideal to recreate this look. With the minor detail that I couldn’t find a 44 inch long (112 cm) two-way zipper. Bah! I can maneuver around that tiny detail by using two zippers instead of one. But with 2 zippers I won’t be able to transform the blazer into a cropped jacket.

Nylon rainbow teeth zipper
NYLON RAINBOW TEETH ZIPPER

But with these eye catching rainbow teeth zippers, the blazer will still have a trendy flare. Each zipper is 21 inches long (55 cm) and not long enough to go all around the blazer. No worries I will make it work.

Let’s decide at which level I want the zippers to be.

I will sew the zippers at waist level www.cardinalsewingnest.com
I WILL CUT THE BLAZER AT WAIST LEVEL

I thought that waist level would be a good visual placement for the zippers.  Since I could not cut the blazer in two completely separate pieces, I decided that the zippers would only open up to the blazer laterals (side seams).

Now, let’s cut with confidence!

Black faux leather blazer refashioned by Cardinal Sewing Nest
CUT AT WAIST LEVEL

The waist level is at 11 inches (28 cm) from the blazer bottom hem. I cut the blazer fabric and the lining up to the laterals and marked the 11 inches (28 cm) measure all around the blazer. Even though the zippers won’t open past the side seams, they still will be sewn all around the blazer.

(Note: If you are lucky enough to find a two-way zipper that is the same length as the circumference of your blazer , cut your blazer all the way around).

Now let’s finish the blazer and lining edges that we just cut.

Measure the zipper width
MEASURE THE ZIPPER WIDTH

Measure from point A to point B. This is where you will stitch the zipper in place. For this zipper the distance is 1 inch (2.5 cm).  That measure is the distance needed between the two pieces of blazer to be able to open the zippers.

 Finish the edges
FINISH THE EDGES

Step 1- Fold inward the edges of both the lining and the blazer. I folded 3/8 of an inch (1 cm) on each cut side. This created a 3/4 of an inch (1.9 cm) gap between the hemmed edges. You will note that the 3/4 of an inch gap (1.9 cm), is less then the 1 inch (2.5cm) “A to B” measure which will allow me to catch the blazer fabric when I sew on the zippers.

Step 2- Close the openings by top stitching the edges of the blazer and the lining together. Top stitch near the edges.

This is how your openings should look like, if  like me, you have chosen to not open the zippers all of the way around your blazer.

(Note: If you have a two-way zipper long enough to be sewn all around the blazer, follow the same steps all along both pieces of your blazer).

The openings ready for the zippers
FINAL RESULT

In the above pictures you can see how the hemmed edges look from inside the blazer. The first picture is a close-up of one side opening. The second picture shows you the complete blazer with both openings top stitched closed and ready for the zipper to be sewn on.

How to finish the edges if your blazer doesn’t have a lining.

If you have a two-way zipper long enough to be sewn all around the blazer.
FOLD THE BLAZER EDGE OVER THE RIGHT SIDE

Fold the cut edge on the right side of the fabric and not on the wrong side of the fabric. This way, the fold allowance will be hidden under the zipper tape, giving you a nice clean finish from the inside of your blazer.

Now the zippers:

Place and pin the zippers face up on the right fabric side of the blazer over your hemmed gap. Ensure that you center the zipper teeth between the hemmed gap that we created (from the front lapel to the lateral seam). That is less than your zipper length. Continue to pin the entire length of the zipper. IE, past the gap which end at the side seam.

Attach the standard zipper foot to the sewing machine.

 Glue or baste the zipper in place
GLUE OR BASTE THE ZIPPER IN PLACE BEFORE SEWING

I glued the zippers in place before sewing them on, and I topstitched both sides of the zipper tapes. I top stitched twice, because I was too lazy to change and thread a double-needle.

As you see in the first above image ,  I folded the zipper tape ends onto themselves so they arrived even with the  blazer edges.

The second picture above shows the space between my two zippers in the back of the blazer. Hum, I really wasn’t missing much, but it is all right, it is an unnoticeable detail.

Below; an inside the blazer view of the sewn zippers.

 inside view of stitches
ZIPPERS SEWN ON THE BLAZER

In the middle image above, you can see that I needed to do a  few hand sewn stitches on the lining where the openings ended. Sometimes in refashioning, it is not perfect you just have to make it work,

Below is an outside blazer view of the sewn zippers.

And, here is the final result;

FINAL COST $21 , INCLUDING  $14  FOR THE TWO ZIPPERS
Black faux leather blazer refashioned by Cardinal Sewing Nest
2 HOURS PROJECT

 

 

 

 

 

 

 

 

 

Leave a Reply

Your email address will not be published. Required fields are marked *